Brick Step Cleaning
Dark and green buildup was cleaned from the brick steps and entry landing, revealing the brick pattern across the treads.
Fort Lauderdale, FL
Paver Cleaning & Sealing in Fort Lauderdale
Our Fort Lauderdale paver-restoration process separates deep cleaning and joint preparation from coating day, then finishes with ASTM-144 joint sand and two coats of Trident Hurricane CAT-5 topical urethane.
⭐ 200+ five-star Google reviews
✅ Surface-Specific Cleaning Methods
📍 Fort Lauderdale Local
📞 Clear, Detailed Quotes
Brick & Paver Cleaning: Before and After
A closer look at cleaning on brick steps, a paver patio and a brick walkway. Sealing is a separate service, quoted when appropriate for the surface.
Paver Patio Cleaning
Cleaning reduced the dark surface buildup and growth between the patio pavers, bringing the block pattern back into view.
Brick Walkway Cleaning
The green film along this narrow brick passage was cleaned away, exposing the brick faces and joints.
Real Fort Lauderdale Paver-Restoration Results
These completed driveway projects show what proper cleaning, joint preparation, sanding, and topical sealing can change.
Before
After
Driveway Cleaning, Re-Sanding & Sealing
The driveway was cleaned to remove organic buildup and expose the joints, then stains and joint debris were addressed before ASTM-144 joint sand was installed. After the surface was ready, two coats of Trident Hurricane CAT-5 enhanced the existing paver color and stabilized the joint sand.
Before
After
Color-Enhancing Topical Sealer Finish
This project shows the richer, semi-gloss wet look produced by CAT-5's T3 True Tone Technology. The two-part water-based urethane is topical and film-forming—not a penetrating sealer—so surface preparation and dry conditions matter before either coat is applied.
Why Choose Bentz for Paver Sealing Fort Lauderdale
Our two-day-minimum restoration process is built around preparation, product knowledge, and clear cure guidance—backed by 200+ five-star Google reviews.
- Day 1 cleaning, stain treatment, joint extraction, and ASTM-144 joint-sand installation
- Day 2 application of two full coats after surface and joint conditions are ready
- Trident Hurricane CAT-5 two-part water-based urethane with a semi-gloss wet look
- Project-specific cure and vehicle-return instructions based on weather and site conditions
Our Two-Day-Minimum Paver-Sealing Process
Day 1: clean and prepare. We clean the pavers, treat applicable stains, extract debris and failed material from the joints, inspect drainage and old coatings, and install ASTM-144 paver joint sand. ASTM-144 sand is not polymeric sand. Borders, drains, low areas, and transitions receive extra attention because trapped moisture or poor joint preparation can undermine the finish.
Day 2: apply two full coats. Once the surface and joints are ready, we apply two coats of Trident Hurricane CAT-5. CAT-5 is a professional two-part, water-based urethane topical sealer. It is film-forming rather than penetrating. T3 True Tone Technology deepens the pavers' existing color and creates a semi-gloss wet look, while Armor Bond helps harden the joint sand.
Cure before return to use. The coating needs protected time after the final coat. Light foot traffic may be possible before vehicle traffic, which often requires 48 to 72 hours, but Fort Lauderdale humidity, shade, drainage, temperature, and the specific site can change that window. We provide the return-to-use instructions for each project; do not drive on the surface until the team clears it.
Every proposal is based on the paver type, square footage, stain load, joint condition, drainage, existing coating, and access. Call (954) 235-9434 or request an estimate through our contact page. For cleaning without sealing, compare our driveway cleaning and pool deck cleaning services.
Frequently Asked Questions — Paver Sealing in Fort Lauderdale
How often should pavers be resealed in South Florida?
Resealing timing depends on the existing coating, UV exposure, drainage, vehicle traffic, cleaning history, and how the finish is wearing. We inspect the surface before recommending a new sealing cycle.
Does Trident Hurricane CAT-5 change the color of my pavers?
CAT-5 uses T3 True Tone Technology to deepen the pavers' existing color and create a semi-gloss wet-look finish. Because it is a topical coating, we review the current paver and any old sealer before application.
How long does paver sealing last?
Service life varies with preparation, drainage, moisture, sun exposure, traffic, cleaning practices, and the condition of any prior coating. We do not treat a calendar estimate as a warranty; the surface should be evaluated when wear becomes visible.
How soon can I walk or drive on sealed pavers?
The coating needs protected cure time after the second coat. Light foot traffic may be possible before vehicle traffic, which often requires 48 to 72 hours, but humidity, shade, drainage, and site conditions can change that window. Follow the project-specific return-to-use instructions provided after application.
Why does professional paver sealing take at least two days?
Day 1 is for cleaning, stain treatment, joint preparation, and ASTM-144 joint-sand installation. Day 2 begins only after the surface and joints are ready, when we apply two full coats of Trident Hurricane CAT-5. Separating preparation from coating helps the topical urethane bond and cure as intended.
Serving Fort Lauderdale and Surrounding Areas
Bentz Pressure Washing serves neighborhoods throughout Fort Lauderdale and Broward County:
Plan the Right Paver Scope
Compare related surfaces, review completed work, or read more about South Florida paver care.
View the Before-and-After Gallery · Read the Paver-Care Guide · Browse Exterior-Care FAQs
Plan Your Paver-Restoration Scope
Restore and protect your driveway or patio with trusted paver restoration in Fort Lauderdale.